Resin calculator for canvas art

This resin calculator for canvas art is set up for a 16 × 20 in painting with one 1/8 in coat. Type your canvas or panel size to see how much resin to mix, and raise the extra if it will run over the sides.

What are you pouring?
Measurements
Measure in
in
in
in

How thick the resin will be. A flood coat is 1/8 in (3 mm).

Your resin
Mix ratio, A to B
The label's ratio is by
Resin type, extra and densityCoating resin · 15% extra · 1.1 g/ml

Sets how deep one pour can be, so the calculator can split a deep job into layers.

%

For drips, edges and what stays in the cup.

g/ml

For weight. 1.1 is typical. Your label may list it.

How much to mix

Mix in total

25.5 fl oz

22.2 fl oz to fill the shape, plus 15% extra.

2 Add B to 25.5 fl oz 1 Pour A to 12.7 fl oz A B
Part A and part B at 1:1 by volume
1:1 by volumeAmount
Part A (resin)12.7 fl oz
Part B (hardener)12.7 fl oz
Total25.5 fl oz

Thin coat, one pour

Most coating resins level out to about 1/8 in (3 mm) on their own, so this goes on in one flood coat.

Same total: 754 ml · 0.754 L · 0.199 gal · 0.829 kg* · 1.83 lb* *Weight at 1.1 g/ml, an estimate.

How this was worked out
  1. Volume: 16 × 20 × 1/8 in = 40 in³ = 655 ml.
  2. Add 15% extra: 655 ml × 1.15 = 754 ml.
  3. Split 1:1 by volume: part A = 754 ml × 1 ÷ 2 = 377 ml. Part B = 377 ml.
  4. Weight, an estimate: 754 ml × 1.1 g/ml = 829 g.

Resin for canvas and panel sizes

One 1/8 in coat. "With sides" adds 20% instead of 10%, for resin you let run over the edges.

Mixed resin per coat, inch sizes
CanvasTop onlyTop onlyWith sides
8 × 8 in144 ml4.88 fl oz5.32 fl oz
8 × 10 in180 ml6.1 fl oz6.65 fl oz
12 × 12 in324 ml11 fl oz12 fl oz
11 × 14 in347 ml11.7 fl oz12.8 fl oz
16 × 20 in721 ml24.4 fl oz26.6 fl oz
18 × 24 in973 ml32.9 fl oz35.9 fl oz
24 × 36 in1,947 ml65.8 fl oz71.8 fl oz
30 × 40 in2,704 ml91.4 fl oz99.7 fl oz
Mixed resin per coat, cm sizes, 3 mm
CanvasTop onlyWith sides
20 × 20 cm132 ml144 ml
30 × 30 cm297 ml324 ml
30 × 40 cm396 ml432 ml
40 × 50 cm660 ml720 ml
50 × 70 cm1,155 ml1,260 ml
60 × 90 cm1,782 ml1,944 ml

Worked example

A 16 × 20 in painting, one 1/8 in coat, 15% extra

  1. Volume: 16 × 20 × 0.125 = 40 cubic inches, or 655 ml.
  2. Add 15%: 754 ml (25.5 fl oz).
  3. Mix 1:1: 377 ml of part A and 377 ml of part B.

Rule of thumb: one square foot at 1/8 in takes about 9.97 fl oz of mixed resin.

Sides, tape and a level surface

Decide first whether the resin will cover the sides. If it will, let it drip and spread it over the edges with a gloved finger, and use 15 to 20% extra. If not, put tape around the edges as a low wall and the 10% default is enough. Peel the tape once the resin is firm but not hard.

Level the piece before you pour, with a spirit level on the canvas itself. Resin runs to the low side, so a tilted canvas ends up thin in one corner and thick in another.

Stretched canvas sags

Resin is heavy, about 1.1 g per ml. On a stretched canvas the weight pulls the middle down, and the resin pools there. You use more than the maths says and the coat is uneven. Wedge a block or a stack of card under the middle of the canvas, or work on a wooden art panel, which stays flat.

Acrylic paint must be fully dry before resin goes on, often a few days for thick paint. Wet paint under resin can cloud or lift.

Questions

How much resin do I need for a 16 × 20 canvas?

About 25.5 fl oz (754 ml) for one 1/8 in coat with 15% extra. That's 377 ml of each part at 1:1.

How much resin per square foot?

About 9.97 fl oz (295 ml) for a 1/8 in coat, and half that at 1/16 in. Add 10 to 20% extra.

How thick should resin be on a painting?

One flood coat of 1/8 in (3 mm) is usual. It levels to about that on its own and gives a glassy finish. A second coat adds depth.

Do I need extra resin for the sides of a canvas?

Yes, if you let it run over. Add 15 to 20% instead of 10%. If you tape the edges to keep it on top, 10% is enough.