Resin calculator

This resin calculator works out how much epoxy resin to mix for a table top, tumbler, river table, coasters or any mould. Enter the size and your mix ratio to get part A and part B in ml, fl oz or grams.

What are you pouring?
Measurements
Measure in
in
in
in

How thick the resin will be. A flood coat is 1/8 in (3 mm).

Your resin
Mix ratio, A to B
The label's ratio is by
Resin type, extra and densityCoating resin · 10% extra · 1.1 g/ml

Sets how deep one pour can be, so the calculator can split a deep job into layers.

%

For drips, edges and what stays in the cup.

g/ml

For weight. 1.1 is typical. Your label may list it.

How much to mix

Mix in total

65.8 fl oz

59.8 fl oz to fill the shape, plus 10% extra.

2 Add B to 65.8 fl oz 1 Pour A to 32.9 fl oz A B
Part A and part B at 1:1 by volume
1:1 by volumeAmount
Part A (resin)32.9 fl oz
Part B (hardener)32.9 fl oz
Total65.8 fl oz

Thin coat, one pour

Most coating resins level out to about 1/8 in (3 mm) on their own, so this goes on in one flood coat.

Same total: 1,947 ml · 1.95 L · 0.514 gal · 2.14 kg* · 4.72 lb* *Weight at 1.1 g/ml, an estimate.

How this was worked out
  1. Volume: 36 × 24 × 1/8 in = 108 in³ = 1,770 ml.
  2. Add 10% extra: 1,770 ml × 1.1 = 1,947 ml.
  3. Split 1:1 by volume: part A = 1,947 ml × 1 ÷ 2 = 973 ml. Part B = 973 ml. Each is rounded, so they can be 1 ml off the total.
  4. Weight, an estimate: 1,947 ml × 1.1 g/ml = 2,141 g.

How to use the resin calculator

  1. Pick what you're pouring: a table top or tray, a circle, a tumbler, a river table, a set of coasters, or a volume you already know.
  2. Choose inches, cm or mm and type the sizes. Fractions like 1/8 work. Tap a depth button for the usual coats.
  3. Set your mix ratio from the label: 1:1, 2:1 or any other, like 3:1 or 100:45. Say whether the label gives it by volume or by weight.
  4. Read the total to mix and the amounts of part A and part B. Change the unit to ml, fl oz, gallons or weight.
  5. Check the pour note. It says when to pour in layers, and how much to mix for each one.

The share link saves every number in the address, so you can send the plan to a friend or keep it for the next batch. Nothing is stored on a server.

The resin formula

Every epoxy resin calculator does the same thing. It finds the volume of the space the resin will fill, adds a little extra, then splits the total by the mix ratio.

  • Rectangle: length × width × depth
  • Circle: 3.14 × radius × radius × depth
  • Tumbler coat: 3.14 × diameter × height × coat thickness
  • River: length × average width × depth

Worked example: a 36 × 24 in tray, 1/8 in deep

  1. Volume: 36 × 24 × 0.125 = 108 cubic inches.
  2. In ml: 108 × 16.39 = 1,770 ml. In fl oz: 59.8 fl oz.
  3. Add 10% extra: 1,770 ml × 1.1 = 1,947 ml (65.8 fl oz).
  4. Mix 1:1: 973 ml of part A and 973 ml of part B.
  5. Mix 2:1 instead: 1,298 ml of part A and 649 ml of part B.

In metric it's simpler, since one cubic cm is one ml. A 50 × 40 cm board at 3 mm (0.3 cm) is 50 × 40 × 0.3 = 600 ml before the extra. See the resin calculator in ml for metric moulds and grams.

Resin thickness guide

Depth drives the amount more than anything else. Double the depth and you double the resin.

Usual resin depths
CoatInchesmmUsed forResin type
Seal coat1/16 in1.5 mmWood and porous surfaces, before the main coatCoating
Flood coat1/8 in3 mmArt, trays, table tops. Levels on its ownCoating
Thick coat1/4 in6 mmCoasters, shallow moulds, a second flood coatCoating, in one pour at most
Small casting1/2 in12 mmMoulds, flowers, objects set in resinDeep-pour, or coating in layers
Deep pour1 to 2 in25 to 50 mmRiver tables, big mouldsDeep-pour

A flood coat stops at about 1/8 in because thin resin spreads out until it's that thick. To build a thicker coat on a flat piece, pour a second coat once the first has firmed up. For anything deeper than about 1/4 in, a deep-pour (casting) resin cures more slowly and gives off less heat, so it can go on in thicker layers.

Mix ratio, volume and weight

The ratio on the label tells you how to split the total. With 1:1 you use the same amount of each part. With 2:1 you use twice as much resin as hardener. For any other ratio, pick Other and type both numbers. 100:45 works as well as 2.2:1.

Most kits give the ratio by volume, so you pour part A to one line on a graduated cup and part B to the next. The cup in the results shows those two lines. If your label gives the ratio by weight, pick Weight. Part A and part B then show in grams or ounces, ready for a scale.

Don't turn a volume ratio into a weight ratio yourself. Part A and part B often weigh a little different per ml, so 2:1 by volume isn't quite 2:1 by weight. The calculator keeps A and B in the ratio's own terms, whatever unit you pick for the total.

The total weight needs a density. The calculator starts at 1.1 g/ml, which is typical for mixed epoxy, and labels it as an estimate. If your label lists a density or specific gravity, type it in under Resin type, extra and density.

How much extra to add

Some resin always stays on the cup, the stir stick and the spreader. Some runs off the edges. The calculator adds 10% by default. Raise it to 15 or 20% for raw wood that soaks resin in, live edges with bark gaps, or when you let resin drip over the sides. Lower it for a closed mould that you fill to a line.

Resin calculators for each project

Each page opens the calculator set up for that project, with its own size table and tips.

Questions

How do I calculate how much resin I need?

Multiply length by width by depth to get the volume. For a circle, use 3.14 × radius² × depth. One cubic inch is 16.4 ml and one cubic cm is 1 ml. Then add about 10% for drips and what stays in the cup. A 36 × 24 in tray at 1/8 in deep is 108 cubic inches, or 1,770 ml. With 10% extra you mix 1,947 ml.

How much resin do I need for a 12 × 12 canvas?

About 11 fl oz (324 ml) of mixed resin for one 1/8 in coat, with 10% extra. Add more if you let it run over the sides.

What does a 1:1 or 2:1 resin ratio mean?

It's how much part A (resin) you mix with part B (hardener). 1:1 means equal amounts. 2:1 means two parts resin to one part hardener, so a third of the mix is hardener. Your label says which, and whether it's by volume or by weight. Don't change the ratio to speed up curing.

Should I measure epoxy by volume or by weight?

Use whatever your label gives. Most craft kits give the ratio by volume, so you measure in a graduated cup. Some give it by weight, which is more exact for small batches. The two numbers differ, because part A and part B don't weigh the same per ml.

How much does epoxy resin weigh?

Mixed epoxy is usually about 1.1 g per ml, a little heavier than water. So 1 litre weighs about 1.1 kg and 1 US gallon about 9.2 lb. Labels list the exact density or specific gravity. Type it into the calculator to get the weight for your resin.

How much extra resin should I mix?

10% covers most projects: resin left on the cup and stick, and drips over the edges. Use 15 to 20% for raw wood, live edges, or work where resin runs off the sides.

How deep can I pour epoxy resin?

Coating resins usually take about 1/8 to 1/4 in (3 to 6 mm) per pour. Deep-pour resins often take 1 to 2 in (25 to 50 mm). Your label gives the exact limit. Pour deeper projects in layers, and let each one firm up before the next.