Tumbler resin calculator

This tumbler resin calculator is set up for a 20 oz skinny tumbler with two coats. Type your cup's diameter and height to see how much epoxy to mix for each coat, or switch to Fill to cast a cylinder mould.

What are you pouring?
Measurements
Measure in
Tumbler job
in

Around the middle. Wrap a tape and divide by 3.14.

in

Only the part you coat or fill.

in

1/32 in (0.8 mm) is a usual start.

coats
Your resin
Mix ratio, A to B
The label's ratio is by
Resin type, extra and densityCoating resin · 10% extra · 1.1 g/ml
%

For drips, edges and what stays in the cup.

g/ml

For weight. 1.1 is typical. Your label may list it.

How much to mix

Mix 2 batches, each

1.44 fl oz

2.87 fl oz in all for 2 coats, including 10% extra.

2 Add B to 1.44 fl oz 1 Pour A to 0.72 fl oz A B
Part A and part B at 1:1 by volume
1:1 by volumeAllEach coat
Part A (resin)1.44 fl oz0.72 fl oz
Part B (hardener)1.44 fl oz0.72 fl oz
Total2.87 fl oz1.44 fl oz

2 coats

Mix each coat fresh. Let one coat cure as your label says before the next, usually a few hours on a turner.

Same total: 85 ml · 0.085 L · 0.022 gal · 0.093 kg* · 0.206 lb* *Weight at 1.1 g/ml, an estimate.

How this was worked out
  1. Wall area times coat: π × 3 × 8 × 1/32 in × 2 coats = 4.7 in³ = 77 ml.
  2. Add 10% extra: 77 ml × 1.1 = 85 ml.
  3. Split 1:1 by volume: part A = 85 ml × 1 ÷ 2 = 42 ml. Part B = 42 ml. Each is rounded, so they can be 1 ml off the total.
  4. 2 coats: 85 ml ÷ 2 = 42 ml each.
  5. Weight, an estimate: 85 ml × 1.1 g/ml = 93 g.

Resin per coat for each tumbler size

Sizes are typical, and every maker's cup differs a little, so measure yours. Amounts are one coat at 1/32 in, before extra.

Mixed resin for one coat
Tumbler, diameter × heightAreaPer coatPer coat
12 oz lowball, 3.5 × 4 in44 sq in23 ml0.76 fl oz
20 oz skinny, 3 × 8 in75 sq in39 ml1.31 fl oz
20 oz regular, 3.4 × 6.5 in69 sq in36 ml1.2 fl oz
30 oz, 3.9 × 7 in86 sq in44 ml1.49 fl oz
40 oz, 3.9 × 9.5 in116 sq in60 ml2.02 fl oz

Worked example

A 20 oz skinny tumbler, 3 × 8 in, two coats

  1. Wall area: 3.14 × 3 × 8 = 75.4 square inches.
  2. One coat at 1/32 in: 75.4 × 0.03125 = 2.36 cubic inches, or 39 ml.
  3. Two coats with 10% extra: 85 ml in all, 42 ml per coat.
  4. Each coat at 1:1: 21 ml of part A and 21 ml of part B.

Mix each coat fresh, when the one before has cured as the label says.

How to measure a tumbler

Wrap a tape measure around the middle and divide by 3.14 to get the diameter. For a tapered cup, measure the top and bottom and use the average. For the height, measure only the part you coat. Most makers leave a band at the top bare for the lid and lips, and skip the base.

Coat thickness is the hard part to guess. 1/32 in (0.8 mm) is a start that allows for what drips off as the cup turns. If you have resin left after each coat, drop it to 1/64 in. If the coat runs thin, raise it.

Mixing small batches

A tumbler coat is only a few tablespoons of resin, and small batches are easy to get wrong. A few drops off is a big share of the mix, and a bad mix stays tacky. Use small graduated cups, pour to the line at eye level, and scrape the sides as you stir. If your label gives a weight ratio, a scale that reads to 0.1 g is the most accurate way to measure.

Questions

How much epoxy do I need for a 20 oz tumbler?

About 42 ml (1.44 fl oz) of mixed epoxy per coat on a 3 × 8 in skinny tumbler, at 1/32 in with 10% extra. Two coats need twice that.

How many coats of epoxy go on a tumbler?

Usually two. The first seals the glitter or vinyl and the second gives a smooth top. Some makers add a third for heavy glitter.

How do I measure a tumbler for epoxy?

Measure around the middle and divide by 3.14 for the diameter. Measure the height of the part you'll coat, not the whole cup.

Why do I have so much epoxy left over?

Your coat is thinner than the calculator assumes. Drop the coat thickness to 1/64 in, or the extra to 5%, and see what you use next time.

Can I mix a very small amount of epoxy?

Yes, but measure carefully. In a small batch, a few drops off changes the ratio a lot, and the coat may not cure. Graduated cups or a 0.1 g scale help.