Table top epoxy calculator

This table top epoxy calculator is set up for a 72 × 36 in table with a 1/8 in flood coat. Type your table's size to see how much epoxy to mix for the seal coat and the flood coat.

What are you pouring?
Measurements
Measure in
in
in
in

How thick the resin will be. A flood coat is 1/8 in (3 mm).

Your resin
Mix ratio, A to B
The label's ratio is by
Resin type, extra and densityCoating resin · 15% extra · 1.1 g/ml

Sets how deep one pour can be, so the calculator can split a deep job into layers.

%

For drips, edges and what stays in the cup.

g/ml

For weight. 1.1 is typical. Your label may list it.

How much to mix

Mix in total

1.61 gal

1.4 gal to fill the shape, plus 15% extra.

2 Add B to 1.61 gal 1 Pour A to 0.806 gal A B
Part A and part B at 1:1 by volume
1:1 by volumeAmount
Part A (resin)0.806 gal
Part B (hardener)0.806 gal
Total1.61 gal

Thin coat, one pour, big batch

Most coating resins level out to about 1/8 in (3 mm) on their own, so this goes on in one flood coat.

That's a big batch to mix at once. Epoxy heats up as it cures, faster in a full cup, so pour it out soon after mixing or mix it in smaller lots.

Same total: 6,106 ml · 6.11 L · 206 fl oz · 6.72 kg* · 14.8 lb* *Weight at 1.1 g/ml, an estimate.

How this was worked out
  1. Volume: 72 × 36 × 1/8 in = 324 in³ = 5,309 ml.
  2. Add 15% extra: 5,309 ml × 1.15 = 6,106 ml.
  3. Split 1:1 by volume: part A = 6,106 ml × 1 ÷ 2 = 3,053 ml. Part B = 3,053 ml.
  4. Weight, an estimate: 6,106 ml × 1.1 g/ml = 6,716 g.

Epoxy for common table sizes

Amounts include 10% extra. Add more if the resin will run over the edges.

Mixed epoxy per coat
TableSeal coat, 1/16 inFlood coat, 1/8 inFlood coat
Side table, 24 × 24 in21.9 fl oz43.9 fl oz1.3 L
Coffee table, 48 × 24 in43.9 fl oz87.8 fl oz2.6 L
Desk, 60 × 30 in68.6 fl oz137 fl oz4.06 L
Dining table, 72 × 36 in98.7 fl oz197 fl oz5.84 L
Large dining table, 96 × 42 in154 fl oz307 fl oz9.08 L
Bar top, 96 × 24 in87.8 fl oz176 fl oz5.19 L

Worked example

A 72 × 36 in dining table, 1/8 in flood coat, 15% extra

  1. Volume: 72 × 36 × 0.125 = 324 cubic inches, or 5,309 ml.
  2. Add 15% for the edges: 5,309 ml × 1.15 = 6,106 ml.
  3. That's 206 fl oz, or 1.61 gal.
  4. Mix 1:1: 3,053 ml each of part A and part B. Mix 2:1: 4,071 ml and 2,035 ml.

A seal coat first, at 1/16 in, adds about 103 fl oz more.

Seal coat, then flood coat

Bare wood is full of air. When resin goes on, the air rises out as bubbles and the wood soaks up some of the resin. A thin seal coat brushed or spread on first fills the grain. Once it has firmed up, the flood coat goes on smooth.

A flood coat of 1/8 in is the usual top coat, because thin resin spreads until it's about that thick. If you want a thicker top, pour a second flood coat after the first has set. Don't pour 1/4 in at once with a coating resin and hope it stays.

Edges and drips

If you let the resin run over the edges, some of each coat ends up on the floor or the drip tray. Add 15 to 20% for that, which is why this page starts at 15%. Tape the underside of the edge so drips fall clean and don't creep under the table. If you dam the edges with tape instead, 10% is enough.

How far a gallon goes: one US gallon is 231 cubic inches. At 1/8 in it covers 12.8 square feet, and at 1/16 in about 25.7 square feet, before any extra.

Questions

How much epoxy do I need for a table top?

Multiply length × width × 1/8 in for a flood coat, then convert. A 72 × 36 in table takes 324 cubic inches, about 180 fl oz, before extra. With 15% for the edges that's 1.61 gal.

How thick should epoxy be on a table top?

1/8 in (3 mm) per flood coat. That's how thick coating resin spreads on its own. For a thicker finish, pour a second coat once the first has set.

Do I need a seal coat?

On bare wood, yes. A thin seal coat stops the wood soaking up the flood coat and lets trapped air out before the main pour, so you get fewer bubbles.

How much does a gallon of epoxy cover?

About 12.8 square feet at 1/8 in and 25.7 square feet at 1/16 in. Allow 10 to 20% less for drips and soak-in.

How many coats of epoxy does a table need?

Usually a seal coat and one or two flood coats. Two flood coats give a deeper finish and cover any spots the first one missed.