Coaster resin calculator

This coaster resin calculator is set up for a set of four 4 in round coasters, 1/4 in deep. Change the number, the mould size and the depth to see how much resin to mix for the whole set.

What are you pouring?
Measurements
Measure in
Mould shape
pieces
in

Inside the mould.

in
Your resin
Mix ratio, A to B
The label's ratio is by
Resin type, extra and densityCoating resin · 10% extra · 1.1 g/ml

Sets how deep one pour can be, so the calculator can split a deep job into layers.

%

For drips, edges and what stays in the cup.

g/ml

For weight. 1.1 is typical. Your label may list it.

How much to mix

Mix in total

7.66 fl oz

6.96 fl oz to fill the shape, plus 10% extra.

2 Add B to 7.66 fl oz 1 Pour A to 3.83 fl oz A B
Part A and part B at 1:1 by volume
1:1 by volumeAmount
Part A (resin)3.83 fl oz
Part B (hardener)3.83 fl oz
Total7.66 fl oz

One pour

It's within the 1/4 in (6 mm) per pour you set. Check the most your resin can take in one go on the label.

Same total: 227 ml · 0.227 L · 0.06 gal · 0.249 kg* · 0.549 lb* *Weight at 1.1 g/ml, an estimate.

How this was worked out
  1. Volume: 4 × π × (4 ÷ 2)² × 1/4 in = 12.6 in³ = 206 ml.
  2. Add 10% extra: 206 ml × 1.1 = 227 ml.
  3. Split 1:1 by volume: part A = 227 ml × 1 ÷ 2 = 113 ml. Part B = 113 ml. Each is rounded, so they can be 1 ml off the total.
  4. Weight, an estimate: 227 ml × 1.1 g/ml = 249 g.

Resin per coaster

One coaster, mixed resin, before extra. The last column is a set of 4 at 1/4 in with 10% extra.

Mixed resin by coaster size and depth
Coaster1/8 in1/4 in3/8 inSet of 4, 1/4 in
3.5 in round20 ml39 ml59 ml173 ml
4 in round26 ml51 ml77 ml227 ml
4.5 in round33 ml65 ml98 ml287 ml
4 in square33 ml66 ml98 ml288 ml

Worked example

4 round coasters, 4 in across, 1/4 in deep

  1. One coaster: 3.14 × 2 × 2 × 0.25 = 3.14 cubic inches.
  2. Four coasters: 12.57 cubic inches, or 206 ml.
  3. Add 10%: 227 ml (7.66 fl oz).
  4. Mix 1:1: 113 ml of part A and 113 ml of part B.

A set of 6 is one and a half times that. Change How many in the calculator.

Measure the mould, not the coaster

Measure the inside of the mould at the bottom, since that's where the resin sits. Many coaster moulds flare a little toward the top, so a pour to the brim takes more than the bottom size suggests. Then decide how deep to fill: most coasters are 1/4 to 3/8 in thick.

The quickest check is water. Fill one mould to your line with water, pour it into a measuring cup and read the ml. Dry the mould fully, then put that number in the Custom shape and multiply by the number of coasters. Water left in a silicone mould clouds resin, so let it dry well.

Coating resin or casting resin?

At 1/4 in most coating resins are near their limit for one pour, and the calculator says so if you go past it. For thicker coasters, or ones with dried flowers or stones set in, a casting resin is safer, or pour in two layers. Things set in the resin take up space, so you'll need a little less, but keep the 10% extra for what stays in the cup.

Questions

How much resin do I need for 4 coasters?

About 227 ml (7.66 fl oz) for four 4 in round coasters at 1/4 in, with 10% extra. That's 113 ml of each part at 1:1.

How thick should resin coasters be?

Most are 1/4 to 3/8 in (6 to 10 mm). Thinner ones can bend or snap, and thicker ones need a casting resin or two layers.

How do I measure my coaster mould?

Measure the inside at the bottom of the mould. Or fill it with water to your line and measure the water, which gives the volume directly.

Can I use coating resin for coasters?

For coasters up to about 1/4 in, often yes. Check your label's limit per pour. For thicker coasters, use a casting resin or pour in layers.