Deep pour epoxy calculator

This deep pour epoxy calculator is set up for a 24 × 12 in mould, 3 in deep, with a deep-pour resin that takes 2 in per pour. Change the sizes and the resin type to see how many batches to mix and how big each one is.

What are you pouring?
Measurements
Measure in
in
in
in

How thick the resin will be. A flood coat is 1/8 in (3 mm).

Your resin
Mix ratio, A to B
The label's ratio is by
Resin type, extra and densityDeep-pour resin · 10% extra · 1.1 g/ml

Sets how deep one pour can be, so the calculator can split a deep job into layers.

%

For drips, edges and what stays in the cup.

g/ml

For weight. 1.1 is typical. Your label may list it.

How much to mix

Mix 2 batches, each

2.06 gal

4.11 gal in all for 2 layers, including 10% extra.

2 Add B to 2.06 gal 1 Pour A to 1.37 gal A B
Part A and part B at 2:1 by volume
2:1 by volumeAllEach layer
Part A (resin)2.74 gal1.37 gal
Part B (hardener)1.37 gal0.686 gal
Total4.11 gal2.06 gal

Pour in 2 layers

It's deeper than the 2 in (50 mm) per pour you set. Pour about 1 1/2 in at a time and let each layer firm up as your label says before the next. Mix each layer fresh.

Even deep-pour resins rarely go past 2 in (50 mm) in one layer. Your label gives the limit.

That's a big batch to mix at once. Epoxy heats up as it cures, faster in a full cup, so pour it out soon after mixing or mix it in smaller lots.

Same total: 15,574 ml · 15.6 L · 527 fl oz · 17.1 kg* · 37.8 lb* *Weight at 1.1 g/ml, an estimate.

How this was worked out
  1. Volume: 24 × 12 × 3 in = 864 in³ = 14,158 ml.
  2. Add 10% extra: 14,158 ml × 1.1 = 15,574 ml.
  3. Split 2:1 by volume: part A = 15,574 ml × 2 ÷ 3 = 10,383 ml. Part B = 5,191 ml.
  4. 2 layers: 15,574 ml ÷ 2 = 7,787 ml each.
  5. Weight, an estimate: 15,574 ml × 1.1 g/ml = 17,132 g.

How many layers?

Divide the total depth by the most your resin takes in one pour, and round up. Your label gives the limit.

Layers by depth and pour limit
Total depthLimit 1/4 inLimit 1 inLimit 2 in
1 in (25 mm)411
2 in (51 mm)821
3 in (76 mm)1232
4 in (102 mm)1642
6 in (152 mm)2463

Worked example

A 24 × 12 in mould, 3 in deep, deep-pour resin at 2:1

  1. Volume: 24 × 12 × 3 = 864 cubic inches, or 14,158 ml.
  2. Add 10%: 15,574 ml (15.6 L, 4.11 gal).
  3. With a 2 in limit that's 2 layers, so 7.79 L per layer.
  4. Each layer at 2:1: 5.19 L of part A and 2.6 L of part B.

Each layer is over 4 litres, so the calculator warns about heat. Mix it in two or three buckets, or follow the label's largest batch.

Why deep-pour resin is different

Epoxy gives off heat as it cures. A thin coat spreads that heat out. A deep pour holds it in, and the hotter it gets, the faster it cures and the hotter it gets again. Coating resin poured too deep can smoke, crack, yellow or warp the mould.

Deep-pour (casting) resins are thinner and cure much more slowly, often over days, so the heat has time to escape. The trade-off is waiting. Most labels give a window for the next layer: pour too soon and the heat adds up, too late and you may need to sand between layers.

Tips for a deep pour

  • Work in a room at the temperature the label asks for. Cold resin is thick and traps bubbles. A hot room speeds up curing.
  • Keep layers even. A layer that is deep in one corner holds more heat there.
  • Mix slowly and for the full time on the label, scraping the sides and bottom of the bucket.
  • Seal porous wood and mould seams first, so the resin doesn't drain away mid-cure.

Questions

How deep can you pour epoxy in one layer?

Coating resins usually take 1/8 to 1/4 in (3 to 6 mm). Deep-pour resins often take 1 to 2 in (25 to 50 mm), and a few more. The label gives the limit for yours.

What happens if you pour epoxy too thick?

It overheats while it cures. It can smoke, crack, turn yellow, warp the mould or set with ripples. Pour in layers, or use a resin rated for that depth.

How long between deep pour layers?

Follow your label. Deep-pour resins cure slowly, so the window is often a day or more. Too soon builds up heat, too late may need a light sand between layers.

How do I calculate epoxy for a deep pour?

Length × width × depth, then add 10%. A 24 × 12 × 3 in mould is 864 cubic inches, about 14.2 L. Divide by your number of layers to get each batch.

Is deep pour epoxy 1:1 or 2:1?

Both exist, and so do 3:1 and other ratios. Use the one on your label, by volume or by weight as it says, and pick Other in the calculator for anything that isn't 1:1 or 2:1.