River table epoxy calculator

This river table epoxy calculator averages an uneven river for you. Type the river's length, its width at three points and the depth to get the deep-pour epoxy to mix, split into part A and part B at 2:1 or your own ratio.

What are you pouring?
Measurements
Measure in
in

Measure the gap between the slabs at three points. Leave the last two blank if the river is even.

in
in
in
in

Usually the full slab thickness.

Your resin
Mix ratio, A to B
The label's ratio is by
Resin type, extra and densityDeep-pour resin · 15% extra · 1.1 g/ml

Sets how deep one pour can be, so the calculator can split a deep job into layers.

%

For drips, edges and what stays in the cup.

g/ml

For weight. 1.1 is typical. Your label may list it.

How much to mix

Mix in total

3.94 gal

3.43 gal to fill the shape, plus 15% extra.

2 Add B to 3.94 gal 1 Pour A to 2.63 gal A B
Part A and part B at 2:1 by volume
2:1 by volumeAmount
Part A (resin)2.63 gal
Part B (hardener)1.31 gal
Total3.94 gal

One pour, big batch

It's within the 2 in (50 mm) per pour you set. Check the most your resin can take in one go on the label.

That's a big batch to mix at once. Epoxy heats up as it cures, faster in a full cup, so pour it out soon after mixing or mix it in smaller lots.

Same total: 14,925 ml · 14.9 L · 505 fl oz · 16.4 kg* · 36.2 lb* *Weight at 1.1 g/ml, an estimate.

How this was worked out
  1. Average width: (6 + 9 + 7) ÷ 3 = 7.33 in. Volume: 72 × 7.33 × 1 1/2 in = 792 in³ = 12,979 ml.
  2. Add 15% extra: 12,979 ml × 1.15 = 14,925 ml.
  3. Split 2:1 by volume: part A = 14,925 ml × 2 ÷ 3 = 9,950 ml. Part B = 4,975 ml.
  4. Weight, an estimate: 14,925 ml × 1.1 g/ml = 16,418 g.

River table epoxy chart

Length times average river width, in US gallons, before any extra. Find your size, then add 15 to 20%.

Mixed epoxy for the river
River1 in deep1.5 in deep2 in deep
48 in × 4 in0.831 gal1.25 gal1.66 gal
48 in × 6 in1.25 gal1.87 gal2.49 gal
60 in × 6 in1.56 gal2.34 gal3.12 gal
72 in × 6 in1.87 gal2.81 gal3.74 gal
72 in × 8 in2.49 gal3.74 gal4.99 gal
96 in × 8 in3.32 gal4.99 gal6.65 gal
96 in × 10 in4.16 gal6.23 gal8.31 gal

Worked example

A 72 in river, 6, 9 and 7 in wide, 1.5 in deep

  1. Average width: (6 + 9 + 7) ÷ 3 = 7.33 in.
  2. Volume: 72 × 7.33 × 1.5 = 792 cubic inches, or 12,979 ml (3.43 gal).
  3. Add 15%: 14,925 ml, which is 3.94 gal or 14.9 L.
  4. Mixed 2:1: 9.95 L of part A and 4.98 L of part B.
  5. Weight, at about 1.1 g/ml: 16.4 kg.

With a deep-pour resin rated for 2 in, that's one pour. With a coating resin it would take 6 layers, which is why river tables use deep-pour resin.

How to measure an uneven river

A live edge river is never one width. Measure the gap across at one end, in the middle and at the other end, and the calculator averages them. If the river pinches and bulges a lot, measure at more points and type the average in the first box.

Measure the depth from the bottom of the mould to the top of the slabs. If you plan to sand or plane the top flat, the resin should stand a little proud, so add a few mm to the depth.

Why river tables need more than the maths says

Raw slab edges soak up resin, and bark gaps and cracks fill too. Mould seams can leak. That's why this page starts at 15% extra. For very cracked or punky wood, use 20 to 25%, and seal the edges with a thin coat first.

Mix the whole pour in a few batches, not one huge bucket. A big mass of epoxy heats up as it cures, and heat makes it set faster and can crack or yellow it. Follow your label's largest batch size and its recoat time between layers.

Questions

How much epoxy do I need for a river table?

Multiply river length × average width × depth. A 72 in river averaging 7.3 in wide and 1.5 in deep is 792 cubic inches, about 3.43 gal. Add 15 to 20% for soak-in and leaks.

How deep should a river table pour be?

Most river tables are poured the full thickness of the slabs, often 1 to 2 in. Check how deep your resin can go in one pour and split the rest into layers.

Can I pour a river table in one pour?

Only if your resin's label allows that depth in one go. Deep-pour resins often allow 1 to 2 in. Coating resins don't, so a river poured with them needs many thin layers.

How do I measure the width of a river table?

Measure across the gap at both ends and in the middle, then average them. For a very wavy river, take more measurements and average them all.

Why did my river table use more epoxy than I worked out?

Raw wood soaks it up, cracks and bark gaps fill, and moulds can leak at the seams. Seal the slab edges first and add 15 to 25% extra.